Harken Replacement ball bearings Manuale Utente Scaricare il pdf

LOADING BALLS

To load balls in car, hold car on

edge and load lower side with

correct number of balls.

DO NOT OVERLOAD.

Remove two clips from car-loader.

Slide plastic car-loader in so loading

port is on the side of car without

balls. Put one clip on “open” end of

the loader.

Load rest of balls through ball loading

port into empty bearing race. Wiggle

car slightly to move balls into race. Do

not overload. Push car to end clip and

slide on inner clip to prevent car from

rolling back to loading port. Put

car back on track.

INSTRUCTIONS

Replacement Ball Bearings

System A, B and C

Headboard, Batten, and Luff Cars

Mainsail Handling Systems

N15W24983 Bluemound Rd. • Pewaukee, WI 53072 U.S.A.

Telephone: (262) 691-3320 • Fax: (262) 701-5780

Web: www.harken.com • Email: [email protected]

Note: Some car loaders are aluminum and do not have clips. Use tape wrapped around end to secure car. Load

balls by recessing aluminum loader one ball width.

SAVE YOUR CAR-LOADER – Plastic car-loader is used to transfer cars to tracks and to load bearings if they

come out of the car.

TO LOAD CAR ON TRACK – Slide off plastic spring clip from the short end of the car-loader. Line it up with

the end of the aluminum track and roll the car onto the track.

For additional safety, maintenance and warranty information see www.harken.com/manuals or the Harken

catalog.

Maintenance

Warranty

Battcars: Clean by frequently flushing with fresh water. Periodically clean car by squirting a

detergent/water solution into center openings. Roll car back and forth to distribute evenly then

flush bearings with fresh water.

Do not use spray lubricants because ball bearings may skid not roll. Apply one to two drops

of McLube

OneDrop

™

to ball contact surfaces of track. Roll car back and forth through

OneDrop

™

several times to distribute onto bearings. Wipe remaining OneDrop

™

off track.

OneDrop

™

is preferred but you can also use one to two drops of a light machine oil. Too much

oil attracts dirt.

Track: Clean with detergent and water.

IMPORTANT! Exposure to some teak cleaners and other caustic solutions can result in

discoloration of part and is not covered under the Harken warranty.

LOADING BALLS

To load balls in car, hold car on

edge and load lower side with

correct number of balls.

DO NOT OVERLOAD.

Remove two clips from car-loader.

Slide plastic car-loader in so loading

port is on the side of car without

balls. Put one clip on “open” end of

the loader.

Load rest of balls through ball loading

port into empty bearing race. Wiggle

car slightly to move balls into race. Do

not overload. Push car to end clip and

slide on inner clip to prevent car from

rolling back to loading port. Put

car back on track.

INSTRUCTIONS

Replacement Ball Bearings

System A, B and C

Headboard, Batten, and Luff Cars

Mainsail Handling Systems

N15W24983 Bluemound Rd. • Pewaukee, WI 53072 U.S.A.

Telephone: (262) 691-3320 • Fax: (262) 701-5780

Web: www.harken.com • Email: [email protected]

Note: Some car loaders are aluminum and do not have clips. Use tape wrapped around end to secure car. Load

balls by recessing aluminum loader one ball width.

SAVE YOUR CAR-LOADER – Plastic car-loader is used to transfer cars to tracks and to load bearings if they

come out of the car.

TO LOAD CAR ON TRACK – Slide off plastic spring clip from the short end of the car-loader. Line it up with

the end of the aluminum track and roll the car onto the track.

For additional safety, maintenance and warranty information see www.harken.com/manuals or the Harken

catalog.

Maintenance

Warranty

Battcars: Clean by frequently flushing with fresh water. Periodically clean car by squirting a

detergent/water solution into center openings. Roll car back and forth to distribute evenly then

flush bearings with fresh water.

Do not use spray lubricants because ball bearings may skid not roll. Apply one to two drops

of McLube

OneDrop

™

to ball contact surfaces of track. Roll car back and forth through

OneDrop

™

several times to distribute onto bearings. Wipe remaining OneDrop

™

off track.

OneDrop

™

is preferred but you can also use one to two drops of a light machine oil. Too much

oil attracts dirt.

Track: Clean with detergent and water.

IMPORTANT! Exposure to some teak cleaners and other caustic solutions can result in

discoloration of part and is not covered under the Harken warranty.

1 2

Sommario

Pagina 1 - Warranty

LOADING BALLSTo load balls in car, hold car on edge and load lower side with correct number of balls.DO NOT OVERLOAD.Remove two clips from car-loader.

Pagina 2 - Car Replacement Bearings

Car Ball BearingPart No. Description Car Length Size No. Type Order Part No.1792 Headboard Car 35/8” (92 mm)1/4” (6 mm) 521807 Headboard Car 35/8” (92

Commenti su questo manuale

Nessun commento

Harken Replacement ball bearings Manuale Utente

Navigare online o scaricare Manuale Utente per Hardware Harken Replacement ball bearings. Harken Replacement ball bearings User Manual Manuale Utente

Sommario

Commenti su questo manuale

Prodotti e manuali riguardandi Hardware Harken Replacement ball bearings